Sub-Zero Error Code 30 8 05: Ice or Water System Issue
No signal from icemaker for fill. | Icemaker no water valve in sig- No signal from icemaker for fill. | Zone 3 fan speed set too Low, Check wiring and power to ice because fan actually rotating maker too fast Zone 1 evaporator fan Open Verify fan not shorted as fan is.
Written by
Jordan Avery Appliance Repair Content SpecialistPublished August 19, 2026
Content status:
Verified
Error code30 8 05
ApplianceRefrigeration
Affected model seriesBuilt-In BI SWS #4380000 | Integrated Drawer | Integrated Tall & Column
Quick answer
No signal from icemaker for fill. | Icemaker no water valve in sig- No signal from icemaker for fill. | Zone 3 fan speed set too Low, Check wiring and power to ice because fan actually rotating maker too fast Zone 1 evaporator fan Open Verify fan not shorted as fan is.
Model compatibility: Sub-Zero reused visible code strings across series and model years, so 30 8 05 may mean something different on another appliance or generation. Confirm this against your model’s documentation and record your full model number before acting.
Plain language
What this code means
Built-In BI SWS #4380000: No signal from icemaker for fill.
Integrated Drawer: Zone 3 fan speed set too Low, Check wiring and power to ice because fan actually rotating maker too fast Zone 1 evaporator fan Open Verify fan not shorted as fan is.
Integrated Tall & Column: Icemaker no water valve in sig- No signal from icemaker for fill.
Signs
Symptoms you may notice
Ice production may stop, slow down, or become inconsistent.
The dispenser may not deliver ice or water normally.
You may hear repeated fill attempts or notice an unusually long fill cycle.
A visible ice jam, restricted water supply, or unexpected water flow may accompany the code.
Before you call
Safe checks you can make
These are simple, non-hazardous checks only. If anything is unclear, stop and contact a technician.
Check for a visible ice cube jam that can be removed without forcing the mechanism.
Confirm the household water supply valve is open and the accessible supply line is not kinked.
If your model uses a water filter, verify it is installed correctly and not overdue for replacement.
Stop using the dispenser if there is leaking or uncontrolled water flow and arrange service.
Important safety warning. Do not remove electrical covers, test energized circuits, open the sealed refrigeration system, or replace a control board based only on the displayed code.
Please avoid
What not to attempt
Electrical measurements
Control-board access
Refrigerant or sealed-system work
Internal component testing
Get help
When to call a technician
Schedule service if the code returns after a basic reset or owner-safe check, if temperatures are moving outside the normal range, if water is leaking, or if the appliance is no longer performing its primary function. A recurring diagnostic code usually means the control is seeing the same condition again. Professional diagnosis can prevent unnecessary part replacement and can identify wiring, control, sensor, airflow, water-system, defrost, or sealed-system causes that look similar from the display alone.
Seeing this code on your Sub-Zero appliance?
Book a specialist visit for a clear estimate and approval before any repair. Independent service — not affiliated with, authorized by, sponsored by, or endorsed by Sub-Zero.
Some Sub-Zero models allow a stored code to be cleared after the underlying problem is corrected. Clearing the display does **not** repair the cause. If the code comes back, use the series-specific meaning above and arrange diagnosis.
No. A diagnostic code identifies a condition detected by the control system. Wiring, connectors, airflow, power supply, control electronics, or another component can sometimes create the same code.
That depends on temperature and the affected function. If the refrigerator is above a safe food-storage temperature, the freezer is thawing, water is leaking, or an electrical issue is suspected, stop relying on the appliance and schedule service promptly.
Sub-Zero has used several generations of electronic controls. The same visible code can be assigned differently by series, zone, or software generation, which is why model applicability is included on this page.
References
Sources & references
Sub-Zero service knowledge base
Ready to get your Sub-Zero appliance working again?
Book a repair online or call us — clear estimates, approval before any work, and a workmanship warranty on completed repairs.
