Defrost Bi-metal stuck closed. | Defrost Bi-metal stuck closed Verify the bi-metal is closed above 70F. | Verify the bi-metal is closed Zone 3 compressor relay stuck above 28° C; replace defrost bi- open metal if necessary No current detected, no load,.
Written by
Jordan Avery Appliance Repair Content SpecialistPublished August 19, 2026
Content status:
Verified
Error code20 2 01
ApplianceRefrigeration
Affected model seriesBuilt-In BI SWS #4380000 | Integrated Drawer | Integrated Tall & Column
Quick answer
Defrost Bi-metal stuck closed. | Defrost Bi-metal stuck closed Verify the bi-metal is closed above 70F. | Verify the bi-metal is closed Zone 3 compressor relay stuck above 28° C; replace defrost bi- open metal if necessary No current detected, no load,.
Model compatibility: Sub-Zero reused visible code strings across series and model years, so 20 2 01 may mean something different on another appliance or generation. Confirm this against your model’s documentation and record your full model number before acting.
Plain language
What this code means
Built-In BI SWS #4380000: Defrost Bi-metal stuck closed.
Integrated Drawer: Verify the bi-metal is closed Zone 3 compressor relay stuck above 28° C; replace defrost bi- open metal if necessary No current detected, no load,.
Integrated Tall & Column: Defrost Bi-metal stuck closed Verify the bi-metal is closed above 70F.
Signs
Symptoms you may notice
Frost or ice may build up around the evaporator area.
Airflow can become weaker as ice accumulation increases.
The freezer or refrigerator may begin running warmer than the set point.
The compressor may run longer because airflow through the evaporator is restricted.
Before you call
Safe checks you can make
These are simple, non-hazardous checks only. If anything is unclear, stop and contact a technician.
Make sure the door closes fully and inspect for obvious frost buildup without removing panels.
Keep packages clear of vents so normal airflow is not restricted.
Do not chip ice from the evaporator area or apply heat with a hair dryer or heat gun.
If frost returns or cabinet temperature rises, schedule professional service.
Important safety warning. Do not remove electrical covers, test energized circuits, open the sealed refrigeration system, or replace a control board based only on the displayed code.
Please avoid
What not to attempt
Electrical measurements
Control-board access
Refrigerant or sealed-system work
Internal component testing
Get help
When to call a technician
Schedule service if the code returns after a basic reset or owner-safe check, if temperatures are moving outside the normal range, if water is leaking, or if the appliance is no longer performing its primary function. A recurring diagnostic code usually means the control is seeing the same condition again. Professional diagnosis can prevent unnecessary part replacement and can identify wiring, control, sensor, airflow, water-system, defrost, or sealed-system causes that look similar from the display alone.
Seeing this code on your Sub-Zero appliance?
Book a specialist visit for a clear estimate and approval before any repair. Independent service — not affiliated with, authorized by, sponsored by, or endorsed by Sub-Zero.
Some Sub-Zero models allow a stored code to be cleared after the underlying problem is corrected. Clearing the display does **not** repair the cause. If the code comes back, use the series-specific meaning above and arrange diagnosis.
No. A diagnostic code identifies a condition detected by the control system. Wiring, connectors, airflow, power supply, control electronics, or another component can sometimes create the same code.
That depends on temperature and the affected function. If the refrigerator is above a safe food-storage temperature, the freezer is thawing, water is leaking, or an electrical issue is suspected, stop relying on the appliance and schedule service promptly.
Sub-Zero has used several generations of electronic controls. The same visible code can be assigned differently by series, zone, or software generation, which is why model applicability is included on this page.
References
Sources & references
Sub-Zero service knowledge base
Ready to get your Sub-Zero appliance working again?
Book a repair online or call us — clear estimates, approval before any work, and a workmanship warranty on completed repairs.
